Привезли мне такой аппарат: 2001 год с АКЕ. Привезли на эвакуаторе, без коробки, ну и топливных трубок тоже не было... Стояла года полтора, наверное...
Поставили коробку, подключил аккумулятор, загорелись лампочки регулировки уровня, заработал насос. Но, так как надо было еще поднимать машину, отключил подвеску, нажав на кнопки.
Дальше, прокачал насос, завел. А подвеска не работает...
При включении зажигания, лампочки моргнут и все-больше никакой реакции...
Ошибки выдает такие:
00776 level control system sensor left front G78 57-00 electric cirq fail...
01769 sens. for veh. leveling front right G289 57-00 electric cirq. fail...
01575 control switched off 35-00
Вопрос: что и как с этим делать? Как активировать подвеску?
Help! по подвеске.
-
pau Пользователь
- Регистрация:
- 05.03.2012
- Сообщений:
- 30
- Авто:
- Безлошадный? :)
- Поблагодарили 0 раз(а) в 0 сообщениях
- Репутация:
- 10
-
sim_a100_2.3_92 Местный
- Регистрация:
- 15.02.2010
- Сообщений:
- 464
- Поблагодарили 7 раз(а) в 3 сообщениях
- Репутация:
- 13
По Эльзе так
(может еще включить ее стоит)
01575
Control system deactivated
- Control system has been deactivated by customer's workshop
- Perform adaption => Page 01-119
Four-wheel self-levelling suspension system: Self-diagnosis
Basic settings
If the control unit, the vehicle level sender or the entire unit is replaced, the basic setting procedure (Adaption) must be performed. The tolerance for the setpoint specification ( normal level 402 mm) is specified at +/- 5 mm on the axle side.
If the new control system does not stabilize, the engine must be started (it is possible that the pressure in the pressure accumulator is no longer sufficient) and all doors must be closed.
The following values are then learned::
◆ Measured height distance at front left (Channel 01)
◆ Measured height distance at front right (Channel 02)
◆ Measured height distance at rear left (Channel 03)
◆ Measured height distance at rear right (Channel 04)
Test preconditions:
◆ Power supply and fuses for the respective system O.K.
=> Circuit diagram, fault-detection - Electrical System and fitting locations
◆ Connect V.A.G 1551 fault reader => Page 01-4
Working procedure
‒ Position the vehicle on a level surface.
‒ Switch the ignition on.
‒ The basic setting is performed via Function 11 "Log-in".
Perform Function "11 - Log-in"
→ Display: Fast data transfer HELP
Select function XX
‒ Press Buttons -1- and -1-.
→ Display: Fast data transfer Q
11 - Log-in procedure
‒ Confirm the entry using the Q button.
→ Display: Log-in procedure
Enter code number XXXXX
‒ Press Buttons 3, 1, 5, 6 and 4
→ Display: Log-in procedure Q
Code 31564
‒ Confirm the entry using the Q button.
→ Display: Fast data transfer HELP
Select function XX
Entry of the measured height values is performed using Function 10 "Adaption".
‒ Press Buttons -1- and -0-.
→ Display: Fast data transfer Q
10- Adaption
‒ Confirm the entry using the Q button.
→ Display: Adaption
enter channel number XX
‒ Press Buttons 0 and 1
→ Display: Adaption Q
Channel number 01
‒ Confirm the entry using the Q button.
→ Display: Channel 1 Adaption 402 ⇒
Wait
Wait, the vehicle will now be raised automatically to two different height levels.
The following is displayed after completion of adjustment:
→ Display: Channel 1 Adaption 402 ⇒
Enter value for wheel fl
‒ Press the ⇒button.
→ Display: Channel 1 Adaption 402
Enter adaption word 00410
‒ Measure: Value entered = Bodywork reference point relative to wheel centre point in mm e.g.: distance measured: 410 mm
◆ For performance of the measurement see
=> Running gear, front- and 4-wheel drive; Repair Group 43
→ Display: Channel 1 Adaption 402
Enter adaption word 00410
‒ Confirm the entry using the Q button.
→ Display: Channel 1 Adaption 402 Q
Value permissible
‒ Confirm the entry using the Q button.
→ Display: Channel 1 Adaption 402 Q
Store changed value?
‒ Confirm the entry using the Q button.
→ Display: Channel 1 Adaption 402 ⇒
Changed value has been stored
‒ Press the ⇒button.
→ Display: Fast data transfer HELP
Select function XX
‒ Continue adaption for the remaining three wheels.
‒ Channel 02 - Wheel fr
‒ Channel 03 - Wheel rl
‒ Channel 04 - Wheel rr
‒ Always measure the bodywork height on the corresponding wheel.
After entry of the four measured values the entry must be confirmed using Function 10 "Adaption".
→ Display: Fast data transfer HELP
Select function XX
‒ Press Buttons -1- and -0-.
→ Display: Fast data transfer Q
10 - Adaption
‒ Confirm the entry using the Q button.
→ Display: Adaption Q
Enter channel number XX
‒ Press Buttons -0- and -5-.
→ Display: Adaption Q
Enter channel number 05
‒ Confirm the entry using the Q button.
→ Display: Channel 5 Adaption 1
Enter Value 1
‒ Press the ⇒button.
→ Display:: Channel 5 Adaption 1
Enter adaption word XXXXX
‒ Press Buttons 0, 0, 0, 0, 1.
Note:
Press Buttons 0, 0, 0, 0 and 0 if you wish to terminate adaption
→ Display: Channel 5 Adaption 1 Q
Enter adaption word 00001
‒ Confirm the entry using the Q button.
→ Display: Channel 5 Adaption 1 Q
‒ Confirm the entry using the Q button.
The following is now displayed:
→ Display: Channel 5 Adaption 1 Q
No calibration possible
‒ Abort using the C button and repeat the calibration.
Display after successful calibration:
→ Display: Channel 5 Adaption 1 Q
Store changed value?
‒ Confirm the entry using the Q button.
→ Display: Channel 1 Adaption 0 ⇒
Changed value has been stored
‒ Press the ⇒button.
→ Display: Fast data transfer HELP
Select function XX
‒ Basic setting is then completed.
The indicator light goes off.#2 sim_a100_2.3_92, 15.03.2012 06:10
Текущее время: 04:55. Часовой пояс GMT +2.